Waterproofing Chemicals

Service Details:

MASTERCRETE M-81 is a single component 100% acrylic polymer admixture specially developed to improve the properties of cementitious compositions. When it is used with combinations with standard quality of ordinary Portland cement, it enhances the mechanical properties such as bonding (adhesion) with various building materials, flexural, compression and impact strength. It improves the thin section fragility of cement when used as coating.
1. As a bond coat (1:1 ratio) - 40 - 45 sq. ft./ 1 coat (it may vary depending upon the substrate)
2. As a coating (2:1 ratio) - 25-30 sq. ft./ 2 coats 

Service Details:

SikaTop®-109 Seal IN is an elastomeric, liquid applied, crack bridging, two part high performance acrylic polymer modified cementitious waterproofing coating system with high degree of flexibility. It comprises of a liquid polymer and a cement based mix incorporating special admixtures. It is applied to concrete and mortar to prevent water infiltration, particularly in demanding applications and difficult environments.

USES
Waterproofing applications for various structures such as:
▪ Raw water concrete tanks, reservoirs, waste water tanks
▪ Terraces, balconies, sunshades, etc.
▪ Flat and small roofs
▪ Basement and Retaining walls
▪ Swimming pools, fountains, water bodies, canals
▪ RCC gutters, drains and planter boxes
▪ Wet areas like toilets, kitchen, utility, sunk slabs
▪ Lift pits, sump, etc.

Additional Information:

• Delivery Time: 5days
• Packaging Details: 50kg

Service Details:

SmartCare PreApply HDPE 80 is a thick high density polythylene membrane is a multi-layer composite waterproofing material with superior performance, including a layer of high performance PE film, self adhesive polymer layer and a unique particulate layer. Unlike conventional membranes, this forms a bond with the wet concrete poured over it and becomes monolithic part of the structure. This prevents water ingress tracking between the unbonded membrane and structure.
Areas of Application- Basement,Tunnel,Subway,Cave, Other Underground public constructions.

Additional Information:

• Delivery Time: 5days
• Packaging Details: Width: 1.2m Length: 20m

Service Details:

Asian Paints SmartCare self-adhesive SBS membrane with HDPE lining is a cold applied self-adhesive waterproofing membrane based on SBS modified bitumen. The bitumen compound is laminated onto an impervious, non-perforated, high performance cross laminated HDPE film. The membrane is protected on the self-adhesive side with a release film. This membrane is used as waterproofing/ damp proofing layer over hardenconcrete by using bitumen primer. It may be used for horizontal and vertical application and as a damp proofing course for tanking below ground structures, subways and retaining walls, tunnel, Cave and other underground constructions
AREA OF APPLICATION: 

• It may be used for horizontal and vertical application and as a damp proofing course for tanking below ground structures, subways and retaining walls,
• tunnel, Cave and other underground constructions

Additional Information:

• Delivery Time: 5days
• Packaging Details: Width: 1mtr Length: 20mtr

Service Details:

Ever since being established in 2005, Rajesh Infrastructure Pvt. Ltd. has been indulged in Trading and Service Providing such as Waterproofing Service, Coating Service, Foundation Grouting Services, PVC Membrane and many more. These are highly demanded by industrial and commercial for use in various areas.

Service Details:

 Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2- component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. 

Service Details:

Primer for sika® range of joint sealants and elastic adhesives for the construction industry.

Additional Information:

• Packaging Details: 500g x 2 metal bottles

Service Details:

Sikaflex®-11 FC is a one-component, gun-grade, adhesiveand sealing compound of permanent elasticity. Thisdual-purpose material is based on a special moisturecuredpolyurethane with an accelerated curing timethat meets ASTM C920 Type S, Grade NS, Class 12.5,Use NT, I, M, G, A, O. and Federal Specification TT-S-00230C.

Service Details:

SikaTop® Seal-107 is a two part acrylic polymer modified cementitious liquid applied waterproof coating system. SikaTop® Seal-107 is used for external and/or internal waterproofing in the following structures: Water-tanks, Basement, Terraces, and balconies, Bridges, Retaining walls, Sea walls, Flat roofs.

Uses:

• Sewage treatment facilities including concrete tanks, digestors, clarifiers etc...
• Water treatment facilities.
• Waterproofing basement and cellars.
• Terraces and balconies.
• Bridges & Sea walls.
• Retaining walls & for sealing “hairline” cracks in concrete structures not subject to movement surfaces.
• Swimming pools and waterproofing of drinking water tanks and reservoirs.

Advantages:

• Pre-batched components.
• Mixed and applied easily & it can be spry applied
• Slurry or trowelable consistency.
• Good adhesion to sound substrates.
• Impermeable and protection against concrete carbonation (80 microns SikaTop Seal-107 is equivalent to 6 inches of concrete).
• Increased frost and salt resistance.
• Non-toxic and slightly flexible.
• Non-corrosive to steel or iron & over-paintable

Coverage:
Depending on type of application, two (2) coats always required. Three (3) coats may be required in areas of extremely high infiltration.1st coat consumption 1-1.5 kg/m2on damp surface.2nd coat consumption 0.8 - 1 kg/m2approx.
Application Mixing
The consistency of the mix can be altered by reducing the amount of component (A) (liquid) to be used. Under normal circumstances, when the full quantities of both components are mixed together, a slurry consistency will result. For a trowelable consistency use only 90% of component (A) (approx. 4.5 kg) Mix in a clean container by slowly adding the powder component to the liquid component and stirring with slow speed mixer.
Cleaning
Do not leave material to harden before cleaning tools and equipment with water.Hardened material can only be removed mechanically.
Curing
As with all cement based products, curing is important. Protect newly applied product against direct sunlight, wind, rain and frost In severe heat and/or wind, protection of the SikaTopSeal-107 is recommended For water tanks and swimming pools, it is essential to cure SikaTopSeal-107 immediately after application for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. Use polythene sheeting or similar approved methods

Additional Information:

• Production Capacity: Unlimited
• Delivery Time: 5-7 Days
• Packaging Details: Packaging 25 kg (A+B

Service Details:

Sika® Extender T is an inert, fine, white, fibrous polymer powder used as a thickening agent for Sikafloor® flooring resins. Suitable for use in hot and tropical climatic conditions.

Additional Information:

• Packaging Details: 1Kg

Service Details:

Sikalastic®-901 is a two-part, elastic, crack-bridging, rapid-curing polyurethanemembrane. Sikalastic®-901 is for machine application only.

• For use as a waterproofing membrane for roofs in both new construction and refurbishment projects with an additional top coat for UV-protection.
• For use as a waterproofing membrane for concrete, metal, pedestrian decks etc.
• For cost efficient life cycle extension of failing roofs
• To be combined with unique vapour transmitting system for water vapour release.

Additional Information:

• Packaging Details: 200KG

Service Details:

SikaProof® A-12 HC is a fully bonded, composite sheet membrane waterproofing system for reinforced concrete structures designed for use in hot climate areas. It consists of an embossed polyolefin (FPO) based membrane laminated with a unique sealant and a non-woven fleece with a self-adhesive strip on the longitudinal side for the overlap. SikaProof® A-12 HC is cold-applied and pre-applied, as it is installed without heat or open-flames, and before the steel reinforcement is fixed and the concrete is poured. Suitable for use in hot and tropical climatic conditions.

Service Details:

MasterTop 100 is a pre-mixed, dry-shake surface hardener and contains a hydraulic binder and specially graded mineral aggregates. The dry powder is broadcast over freshly laid concrete and is power-floated to produce a tough, smooth and coloured finish. MasterTop 100 is available in certain colours.

TYPICAL APPLICATIONS:

•  Aircraft hangars. 
•  Basements and cellars. 
•  Mechanical workshops. 
•  Garage for light vehicles.
•  Storage rooms. 
•  Corridors and halls. 
•  Parking areas. 
•  Loading platforms. 

Additional Information:

• Delivery Time: 5days
• Packaging Details: 25kg

Service Details:

It is a waterproof, Bituminous Tape, that bonds securely to any substrate like brickwork, concrete, wood, metal, tiles, roofing sheets, glass & most rigid plastics. 

Service Details:

Sikafloor®-21 PurCem® LP is a three part, water dispersedmedium to high strength coloured polyurethanemodified, cement and aggregate screed with selfsmoothing properties.It has an aesthetic, smooth textured aggregate surfaceproviding medium slip resistance and is typically installedat 3 to 6 mm thickness.

Service Details:

Asian Paints SmartCare Crack Seal is a ready to use fiber glass reinforced crack filling compound for both interior and exterior surfaces. It ensures unmatched crackbridging ability for plaster cracks of up to 3 mm.

Additional Information:

• Production Capacity: Unlimited
• Delivery Time: 2 - 3 Days

Service Details:

Sarnacol®-2142 V is a VOC free, 1-part, polyurethane based moisture curing adhesive. 
Bonding Sarnafil® G Felt-type and Sarnafil® T Felt-type membranes to roof substrates. Bonding substrates:
 Concrete
 Oriented fibre strand boards, plywood panels
  Slated/mineralized bitumen sheets; new and aged Mineral fibre boards: product specific approval with sufficient compressive strength and appropriate surface for bonding
 PIR insulation boards: product specific approval with appropriate surface for bonding
 EPS insulation boards: product specific approval with appropriate surface for bonding
 Steel panels: product specific approval with appropriate surface for bonding